Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Fort Worth Homeowners
When a gate stops opening, sags on its hinges, or starts grinding against the track, Fort Worth homeowners need a repair tech who can fix it properly the first time, not just quiet the symptom for a few weeks. Our Automatic Gate Repair service covers both mechanical and electrical failures. Gate repair in Fort Worth typically costs between $150 and $600 for most mechanical and structural fixes, with opener problems landing in the $180 to $450 range before parts. Calder Gate Repair Fort Worth has been doing this work since 2009 as part of the Relay Home Co. family, and we send background-checked, uniformed technicians with a live, trackable arrival time so you know exactly when help shows up. Call (682) 432-9830 any hour, any day. A real person answers.
Driveway Gate Repair
Driveway Gate Repair is the work of getting a residential gate swinging or sliding correctly again after hinges bind, posts shift from North Texas clay soil movement, or an opener burns out from running against resistance. Fort Worth homes in neighborhoods like Monticello, Ryan Place, and far north toward Saginaw deal with steel frame gates and heavy iron panels that settle over time. Calder Gate Repair Fort Worth handles the full driveway gate repair scope: Gate Realignment, replacing hinge brackets, rewiring opener connections, and correcting track alignment on slide gates. Most driveway gate repairs run $180 to $450 before any replacement parts, and we write that price down before we touch a single bolt.
Hinge and Post Realignment
When a driveway gate starts dragging at the latch side, the culprit is almost always a post that has shifted or a hinge pin that has worn into an oval. We level the leaf, shim or reset the post where needed, and replace worn pins with the correct diameter as part of our Hinge & Post Repair service. If the gate still binds after adjustment, we say so and quote the repair rather than grinding away material to force it closed.
Opener Stress Repairs
A driveway gate opener that whines or trips its breaker is often fighting a misaligned gate. We measure the force required to move the leaf and compare it to the opener’s rated duty cycle. That tells us whether the fix is mechanical, electrical, or both, and the written estimate reflects the actual fix rather than a guess.
Styles & brands we work with
Gate Welding
Gate Welding is how we repair cracked steel frames, snapped hinge plates, and broken pickets on metal gates across Fort Worth. When a weld fails, the gate usually keeps working for a while, but every cycle stresses the crack further until a hinge tears off or a corner drops. Calder Gate Repair Fort Worth performs on-site MIG and stick welding for most residential and light commercial gate frames. Gate welding and related metal fabrication typically runs $200 to $600 depending on the number of stress points, the thickness of the steel, and whether we need to remove the leaf to weld it on the ground for proper penetration.
Cracked Frame Stitching
We grind out the crack to clean metal, bevel the edges, and lay a full-penetration root pass with a cover pass over top. Sanding and primer follow so the repaired joint doesn’t stand out or rust through in a season. On ornamental work, we match the bead profile to the original so it disappears under paint.
Hinge Plate Replacement
When the hinge plate tears away from the stile, welding it back in place without addressing the frame flex just moves the failure point. We cut out the fatigued section, weld in a gusseted plate, and re-hang the gate with the leaf properly balanced. That fix typically outlasts the original factory weld.
Commercial Gate Repair
Commercial Gate Repair covers the heavier-duty gate systems on apartment complexes, warehouses, HOAs, and business lots throughout Fort Worth. These gates cycle dozens or hundreds of times a day, run on industrial operators, and have to work every single time or the property owner starts taking angry phone calls. Calder Gate Repair Fort Worth services commercial slide gates, barrier arm gates, and swing gates with the same written-price rule we use for residential work. Commercial gate repair in Fort Worth generally runs $300 to $900 for most failures, with a site visit and written quote included before any work begins.
High-Cycle Operator Diagnostics
A commercial operator that overheats or faults at peak hours is telling you something: worn capacitors, binding track wheels, a failing limit switch, or a control board that has lost its settings. We test line voltage under load, inspect the motor windings, and run the gate through full cycles while watching amperage draw. The diagnosis is written down, along with the exact parts and labor to fix it.
Track and Wheel Service on Slide Gates
Over time, commercial slide gates wear grooves into the track rollers and the V-track itself, which loads the motor harder every cycle. We replace hardened wheels, dress the track surface where practical, and tune the gate’s travel so it coasts into the stops instead of slamming them. Proactive wheel service avoids a blown chain or sheared sprocket down the road.
Iron Gate Repair
Iron Gate Repair restores strength and smooth operation to forged and cast iron gates, which Fort Worth has in abundance in older neighborhoods like Fairmount and the historic districts around downtown. Cast iron is rigid and brittle, so when a hinge lug cracks or a decorative scroll snaps, you do not just weld and walk away; you have to control the heat. Calder Gate Repair Fort Worth works with both cast and wrought iron, using nickel rod or brazing where the metal mix demands it. Iron gate repair typically runs $180 to $550 depending on whether the work is structural, decorative, or both.
Cast Iron Crack Control
We preheat the area around the break, weld with low-hydrogen or nickel-alloy filler, and cool the repair slowly under a heat blanket. Skipping that process leads to a new crack right next to the weld within a year. It’s slower, but we do it the way the material demands.
Scroll and Ornament Restoration
Broken decorative scrolls and finials do not usually affect how the gate works, but they do make a property look neglected. We fabricate replacement scrollwork to match the original pattern, weld it in, and dress the joint so it reads as original. If a full replacement part is available from a foundry supplier, we quote that option alongside.
Sliding Gate Repair
Sliding Gate Repair fixes cantilever and V-track slide gates that bind, jump the track, or stall halfway across a driveway. Fort Worth’s flat lots in places like Haltom City and Richland Hills make sliding gates a practical choice, but they punish neglect: a seized wheel bearing or a sagging top guide will smoke an opener in weeks. Calder Gate Repair Fort Worth resets rolling gear, adjusts guide heights, and replaces wheel assemblies on all common slide gate configurations. Sliding gate repair typically runs $200 to $500, with opener diagnostics billed separately if the mechanical side is fine.
Roller and Bearing Service
A slide gate should move with one hand on the rail. If it does not, we pull the wheel assemblies and inspect the sealed bearings, axle bolts, and wheel faces for flat spots. Replacement wheels with greased, shielded bearings get the gate rolling clean again and take load off the operator.
Guide and Stop Adjustment
Top guide rollers that are too tight or too loose cause the gate to bang around in the wind or lean out of plumb. We set the guide clearance to the gate’s actual thickness, align the end stops so the gate does not overtravel, and verify the chain or belt tension matches the operator’s spec. That last part matters: too tight and the motor’s output shaft loads up, too loose and the gate jumps under acceleration.
Wrought Iron Gate Repair
Wrought Iron Gate Repair focuses on gates built from true wrought iron or modern mild steel styled to look like it, common in Fort Worth’s custom-home neighborhoods like Mira Vista and along the city’s western edge. Wrought iron resists corrosion better than raw steel, but the joinery is often riveted or forge-welded, which means repairs need a different approach than a simple MIG bead. Calder Gate Repair Fort Worth fabricates, welds, and refinishes wrought-style gates to preserve their look and their strength. Most wrought iron gate repair jobs land between $180 and $500 depending on the size of the break and whether we need to match decorative work.
Rust Remediation and Touch-Up
Surface rust on a wrought iron gate is common after North Texas springs and summer humidity. We wire-brush or needle-scale the affected areas, apply a rust-converting primer, and finish with a satin black or custom-matched color so the patch does not flash against the original finish. It is a preventative step that keeps a small cosmetic issue from turning into metal loss.
Section Replacement
When a bottom rail has rusted through or several pickets are too far gone to weld, replacing the section is cleaner than stacking repairs on top of decay. We cut the damaged area back to solid metal, form or order a matching replacement piece, and weld it in with the same spacing and profile as the original. The gate keeps its pattern and the repair does not show.
Metal Gate Repair
Metal Gate Repair is the broad category for gates built from steel, aluminum, or a mix of both, which covers most modern Fort Worth gates from the 90s onward. Aluminum is lighter and rotproof but much easier to tear at hinge points, while steel is strong but rusts at weld joints if the factory coating fails. Calder Gate Repair Fort Worth works both materials and knows when to weld, when to bolt, and when a replacement section is cheaper than fixing the old one. Typical metal gate repair work runs $150 to $450, with the higher end involving frame damage or seized hardware.
Aluminum Gate Stress Points
Aluminum gates usually fail at the corner welds or where the hinge plate bolts through the stile. We evaluate the wall thickness before deciding on a repair path; on thin-wall tubing, drilling and bolting a full-length backing plate distributes load better than welding in the same spot twice. That repair path avoids the cycle of re-welding the same corner every year.
Steel Frame Reinforcement
When a steel gate sags but the post is plumb, the frame itself is often flexing. We weld a diagonal brace or a gusset plate where the top rail meets the hinge stile, which changes how the gate carries its own weight. After reinforcement, we re-hang the leaf and tune the latch so it closes without lifting.
Wood Gate Repair
Wood Gate Repair stabilizes and restores cedar, pine, and redwood gates that have sagged or separated due to Fort Worth’s seasonal moisture swings and summer sun. Wood gates fight two forces at once: gravity pulling the free corner down and temperature changes swelling and shrinking the boards. Calder Gate Repair Fort Worth replaces rotted rails, upgrades soft wood to pressure-treated or cedar stock, and installs anti-sag hardware the right way. Wood gate repair in Fort Worth generally runs $150 to $400 depending on whether we are rebuilding a panel or just squaring and refastening one.
Frame and Rail Replacement
A wood gate that drags at the latch has usually rotted at the bottom rail or the hinge side. We remove the rotted rail, cut a replacement from cedar or pressure-treated lumber, and refasten the boards with stainless or exterior-rated screws. The gate gets squared on a flat surface before it goes back on the hinges.
Anti-Sag Kit Installation
An anti-sag kit is a cable and turnbuckle that runs diagonally from the top hinge corner to the bottom latch corner, pulling the low side back into square. We install the kit with through-bolts where possible, not short lag screws that tear out in a season. After adjustment and a few open-and-close test cycles, the gate latches without a shove.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
Fort Worth gates run on all kinds of openers, and we have spent real time inside the ones homeowners actually own. We service Ghost Controls, DoorKing, Elite, and Mighty Mule units regularly, among others. On Ghost Controls kits, the common failures we see are stripped clutch plates and corroded transformer contacts; we stock replacements for both. DoorKing slide gate operators in commercial settings usually need limit switch rewiring or loop detector calibration, which we handle on site with the correct test equipment. Elite and Mighty Mule swing gate arms tend to fail at the battery or the control board after storm surge events, and we keep those parts on the truck during storm season. Whether your opener is one of those brands or something else entirely, the diagnostic process is the same: test voltage in, test signal out, and isolate the fault before quoting a fix. You can also see our dedicated electric gate repair or gate opener repair pages for a deeper look at how we handle control systems.
Signs You Need a Pro Right Now
- The gate moved slower than usual this morning. A slow cycle means the opener is working against extra resistance. A failing capacitor or a binding hinge both show up as sluggish movement, and catching it now costs less than replacing the motor later.
- You heard a metal-on-metal grind near the track or hinge side. Grinding means two surfaces are rubbing that should not be. On a sliding gate, a seized wheel bearing can dig into the track and destroy an $80 rail section; on a swing gate, a snapped hinge pin starts wearing the stile into an oval.
- The opener runs but the gate does not move. That combination usually points to a sheared drive chain, a stripped gear, or a disconnected arm. Running the opener any longer while it strains against a broken link can burn out the motor, so cut power at the breaker and call.
- The gate sags enough to drag at the latch side. Sagging is a symptom, not the problem itself: the post has shifted, the frame has flexed, or the wood has rotted. Ignoring it turns a $200 realignment into a $600 frame rebuild when the hinge finally tears out.
- The remote works intermittently or only when you are standing close. That is usually a failing receiver board or antenna connection, not a battery. If you replace the battery and the range is still garbage, the problem is in the opener electronics and it will not fix itself.
Our Process, Step by Step
- 1
Call or book, and talk to a human. You call (682) 432-9830 and a live person answers, 24/7. We ask what the gate is doing, what brand the opener is, and whether this is urgent, then schedule a visit with a live, trackable arrival time.
- 2
Diagnostics on site. The technician tests mechanical operation first: hinge wear, track alignment, post plumb, and opener force settings. For electrical faults, we use a multimeter to chase voltage through the control board, transformer, and limit switches rather than swapping parts on a guess.
- 3
Written price before any work. After the diagnostic, we walk you through what we found and hand you a written quote for the repair. The number on that paper is the number on the invoice unless you approve a change in scope in writing first.
- 4
Repair and verification. We complete the work, cycle the gate through multiple open and close tests, and adjust limits and force settings so the system runs within spec. Before-and-after photos go on the invoice.
- 5
Digital invoice and the 365-Day Done Right Promise. You get a digital invoice you can pay from a link, with a written guarantee on every job we do. If the repair fails within 365 days, Calder returns at no charge to make it right.
How Much Does Gate Repair Cost in Fort Worth?
Most gate repairs in Fort Worth run between $150 and $600, with the real variable being the type of failure. A Lock Repair or hinge and post realignment on a standard residential swing gate typically lands at $180 to $350. Sliding gate wheel and track service runs $200 to $500. Welding a cracked frame or replacing a hinge plate costs $200 to $600 depending on access and material thickness. Opener repairs fall between $180 and $450 before parts, and a dead control board on a DoorKing or Mighty Mule unit usually adds $150 to $300 in parts. The factors that move the price: gate size and weight, whether we can work on it in place or need to remove the leaf, rust and corrosion that complicates the repair, and whether the opener is salvageable or needs replacement. The way to avoid overpaying is to get a written diagnostic quote before work starts and to ask what the technician found, in plain language, before approving anything. Every Calder Gate Repair Fort Worth estimate is free and includes a written list of what is wrong, what we recommend, and what it costs. Call (682) 432-9830 for an exact quote on your specific gate. Estimates are free, and no work starts until you approve the number in writing.
Our Service Area Near Fort Worth
Calder Gate Repair Fort Worth covers the whole city, from the south side near Rendon up through Richland Hills, Haltom City, Saginaw, and the western communities of Lake Worth, River Oaks, Sansom Park, and White Settlement. We are also the dedicated gate repair team for Gate Repair in North Richland Hills and Gate Repair in Keller, with the same live arrival time and written-price guarantee. Typical response time across our Fort Worth service area is same-day or next-day, depending on call volume and whether the repair is urgent.
Serving Fort Worth, TX - Our Local Coverage Area
We’re based in the Fort Worth area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Repair in Fort Worth
Gate repair is the process of diagnosing and fixing a gate that won’t open, won’t close, sags, binds, or makes noise it should not make. It covers mechanical work like hinges, posts, and track wheels, plus electrical work on the opener, control board, and safety sensors. At Calder Gate Repair Fort Worth, gate repair always includes a written quote before any work starts and a written guarantee on the completed job. Call (682) 432-9830 for a free estimate.
Most mechanical gate repairs in Fort Worth take 1 to 3 hours on site, and we finish the job the same day in the majority of cases. Welding work that requires removing the gate leaf or fabrication of a replacement section may take a little longer, and we will tell you the timeline before we start. The 365-Day Done Right Promise means if the repair fails within the year, the return visit is free. Call (682) 432-9830 and a live person will let you know when we can get to you.
Gate repair in Fort Worth typically costs between $150 and $600 for the repair labor itself, with opener replacement parts adding $150 to $300 on top when the control board or motor is dead. The written quote we give you includes the full price before any work starts, so there are no surprises at the invoice. Call (682) 432-9830 for an exact quote on your gate and opener setup.
Yes, our technicians are factory-familiar with Mighty Mule and Ghost Controls, along with DoorKing, Elite, and several other major brands. Mighty Mule units often show up with control board failures after storms, while Ghost Controls kits commonly have clutch or transformer issues. We diagnose the opener specifically rather than just swapping the whole unit, which usually saves you money. Call (682) 432-9830 and we will tell you what is wrong and what it costs to fix.
Yes, we answer calls 24 hours a day, 7 days a week, and we schedule emergency gate repair in Fort Worth for situations where the gate is stuck open or stuck closed and security is compromised. A live person answers, takes your information, and dispatches a background-checked technician with a live arrival time you can track. Call (682) 432-9830 if you are dealing with a gate that will not move.
Every repair from Calder Gate Repair Fort Worth includes the 365-Day Done Right Promise: a written guarantee on the work, and if the repair fails within 365 days, we come back at no charge to make it right. The guarantee is stated in writing on every job, not buried in fine print. Call (682) 432-9830 and we will walk you through exactly what the guarantee covers for your specific repair.
Make sure the gate area is accessible, move vehicles back from the gate’s full swing or slide path, and if you have a control box inside the house or garage, know where it is in case we need to check power. If the gate is stuck in one position, leave it there unless it is a safety hazard. Our technician will arrive in uniform with a live arrival time you can track, and you will get a written price before any work starts. Call (682) 432-9830 to schedule.
Schedule Your Gate Repair Service in Fort Worth Today
A gate that is down is not just a fence problem; it is the opening to your property left unguarded. Calder Gate Repair Fort Worth sends a uniformed, background-checked tech with a live arrival time you can track from your phone, a written price before any work starts, and the 365-Day Done Right Promise backing every repair. Call (682) 432-9830 now for a free, no-obligation estimate, any hour, any day. A real person answers.
Written by Nico Alvarez, Owner at Calder Gate Repair Fort Worth, serving Fort Worth since 2009.