Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Opener Repair Across Haltom City
Gate opener repair in Haltom City usually runs $190 – $430 before parts, and most jobs involving a dead control board, stripped drive gear, or failing capacitor can be diagnosed and fixed the same day. Calder Gate Repair Fort Worth answers live 24/7 at (682) 432-9830 and dispatches background-checked, uniformed techs to Haltom City with a trackable arrival time, not a four-hour window. If you’re in Haltom City and your gate won’t open, won’t close, or won’t stop where it should, call us and get a written price before any work starts.
We know Haltom City’s gates because we work on them every week. The older neighborhoods east of Denton Highway, the mid-century brick homes off Broadway Avenue, the light industrial yards near the railroad: they all have their own failure patterns, and we’ve seen most of them. The number on the invoice will match the number we agreed to at the door. That’s not a courtesy, it’s how we operate.
Why Calder Gate Repair Fort Worth Is Haltom City’s Preferred Gate Opener Repair Company
Haltom City homeowners call us because we treat an opener repair like a repair, not a sales pitch. We’ll tell you honestly when a control board can be reflashed and when it’s cheaper to replace it. We’ll show you the failed limit switch, the swollen capacitor, the stripped gear, and explain what it does in plain words before we quote a dollar figure. Calder Gate Repair is the dedicated gate division inside Relay Home Co., founded in 2009 and independently owned and operated. Every job here carries three things in writing: a price before work starts, a written guarantee on the repair, and a free second visit if that repair fails within 365 days under our 365-Day Done Right Promise.
Nico Alvarez leads our Fort Worth-area crews. He’s been on Haltom City service calls where a homeowner expected a simple board swap and we instead found a hinge post leaning two inches out of plumb. We don’t patch over problems like that. We tell you what’s actually wrong, what it costs to fix it properly, and what will happen if you wait. For industrial sliding gates along the Denton Highway corridor, we often carry repaired-to-spec drive gears and safety photocell kits on the truck so commercial gates go back online the same day.
Styles & brands we work with
Gate Intercom in Haltom City
A gate intercom in Haltom City is what lets visitors call your phone from the driveway instead of honking, and in an older brick ranch home with a gated front yard, it’s usually the second most-requested repair after the opener itself. Most intercom repairs here run $140 – $310, depending on whether we’re replacing a handset, rewiring a call button that clay soil movement shorted out, or adding a phone-based unit so you can open the gate remotely.
Wiring and Soil Movement
In Haltom City, low-voltage intercom wiring gets run through conduit buried along fence lines and under concrete aprons. When the expansive clay shifts, that conduit flexes, and the wire insulation inside chafes through. The symptom is usually dead air on the handset or a call button that rings but won’t release the gate. We trace the short, pull new wire through the existing conduit when we can, and quote a new run when we can’t.
Retrofitting Phone-Based Entry
A lot of Haltom City homeowners with 1960s-era intercoms ask if they need to replace the whole system. Often not. We can retrofit a modern keypad or phone-integrated intercom to the existing opener, which means you keep the old call box on the post but add an app-based release that works from anywhere. The retrofit typically lands in the $220 – $380 range before any new wiring.
Gate Opener With Keypad in Haltom City
A gate opener with keypad in Haltom City means you punch in a code and the gate opens, no remote hunting under the seat required. Keypad installs and repairs here run $130 – $260 for a wired unit, and $240 – $430 when we’re adding a wireless keypad programmed to an existing opener, which is common on the tube steel gates around Haltom City’s 1950s-1970s ranchers.
Keypad Failure Patterns in Older Installations
Keypads on Haltom City gates usually fail for predictable reasons. Water gets behind the faceplate during spring storms, the rubber buttons eventually lose their seal, or the low-voltage wires to the keypad get nicked where they exit a concrete post. We replace bad keypads with sealed, UV-rated units and silicone the mounting surface to keep Tarrant County weather out.
Adding a Keypad to a Legacy Opener
If your gate opener predates wireless keypads, that doesn’t always mean a full replacement. Some Linear and Mighty Mule control boards have accessory terminals for an external keypad, and we can wire one in for less than a full operator swap. We’ll tell you upfront if your board won’t support a keypad and give you a replacement opener quote instead of selling you a keypad that won’t work.
Trusted Brands We Service in Haltom City
Our techs are factory-familiar with nine major gate opener brands, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. In Haltom City we see a lot of Ghost Controls and Mighty Mule units on residential swing gates, plus older DoorKing and Elite operators on commercial slide gates near the railroad and Denton Highway. Because we stock common drive gears, control boards, safety photocells, and capacitor kits locally, most Haltom City repairs don’t wait on a parts shipment. If the part is on a shelf in our metro inventory, it’s in the truck the same day.
See the difference
Before
After
Before
After
Before
AfterCommon Gate Opener Repair Problems We See in Haltom City Homes
- Dragging swing gates from settled concrete posts. In Haltom City’s older neighborhoods east of Denton Highway, many chain-link and tube steel gates were hung on un-reinforced concrete posts. Decades of Tarrant County clay movement lean the post into the latch side, and the opener stalls, trips, or burns out its capacitor. The fix is usually cutting and re-welding the hinge brackets at a custom angle, not just cranking the force setting up.
- Shorted low-voltage wiring from conduit flex. Clay soil moves, buried conduit flexes, and the insulation on keypad, intercom, and loop detector wire chafes through. The symptom might be a dead keypad, a gate that opens but won’t close, or an intercom that buzzes instead of talking. We locate and repair the damaged run, then quote proper re-wiring.
- Stripped plastic drive gears on heavy slide gates. Industrial sliding gates near the railroad and Denton Highway are heavy, and when the concrete apron settles unevenly, the rack and pinion teeth bind. That binding strips the plastic gear inside the operator. We replace the gear and re-align the rack, and we’ll tell you if the apron needs re-setting to keep it from happening again.
- Failed safety devices on operators installed before modern entrapment standards. Many Haltom City gates predate current UL 325 safety requirements. Photocells and reversing edges either weren’t there or stopped working years ago. When we open a control box and find a safety input bypassed, we explain the hazard plainly and quote restoring entrapment protection. A gate that can’t reverse is dangerous to people and pets, and it’s a code issue worth fixing.
Pricing for Gate Opener Repair in Haltom City, TX
Most gate opener repairs in Haltom City run $190 – $430 before parts. A typical residential swing gate board replacement lands around $240 – $380 with a standard LiftMaster or linear board. A full operator replacement on a single swing gate usually falls between $850 and $1,500 installed, depending on the brand and whether the hinge posts need correction. A commercial slide gate operator replacement on a Denton Highway property can run $1,200 – $2,800, with rack re-alignment quoted separately if the apron has settled. The three things that move price most in Haltom City are post lean from clay soil, obsolete control boards on pre-2000 operators, and parts availability on discontinued models. Before any work starts, you get a written price that itemizes labor and parts. You’ll never get a surprise invoice. Call (682) 432-9830 and we’ll quote the job before a single bolt gets turned.
One thing worth saying clearly: welding a leaning hinge post back into alignment is sometimes the only honest fix, and it’s usually cheaper than replacing a burned-out opener every two years. On an industrial property near the railroad tracks off Denton Highway, our tech found a Viking slide gate opener that refused to reverse after a spring storm knocked a loop detector out of alignment in the settled concrete apron. We re-set the loop depth, corrected the rack and pinion backlash, and re-tuned the safety photocell so the gate would close without tripping. Then we welded new hinge brackets at a custom angle on the adjacent swing gate, whose post footing had shifted enough to drag the gate on the concrete. That’s what a proper Haltom City gate repair often looks like.
Our Gate Opener Repair team carries the tools and welding equipment to handle that kind of job in one visit, and dispatches from the brand’s Dallas-Fort Worth office to serve Haltom City locally.
We Also Serve Cities Near Haltom City
If you’re just outside Haltom City, we cover the surrounding area too. Calder Gate Repair Fort Worth handles gate opener repair in Fort Worth, North Richland Hills, Keller, and Colleyville with the same written pricing and 365-Day Done Right Promise. So whether you’re in Haltom City proper or a few minutes up Denton Highway, the same team and the same guarantees apply. Learn more about our local coverage on our Gate Opener Repair in Haltom City page.
Serving Haltom City, TX - Our Local Coverage Area
We’re based in the Haltom City area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Opener Repair in Haltom City
Yes, in most cases the hinge post has leaned enough from clay soil movement that the gate leaf is dragging, and cutting and re-welding the hinge brackets at a corrected angle is the durable fix. We won’t know the exact angle until we put a level on the post and measure the gap, but we see this constantly in the neighborhoods east of Denton Highway where original posts were set without reinforcement. Call (682) 432-9830 for a free assessment and written quote.
Usually yes. The gate panel itself is rarely the problem. We can build adapter plates to mount a modern LiftMaster arm to a non-standard hinge geometry, and we’ll re-weld the hinge brackets if the posts have shifted. The retrofit often runs $190 – $430 for the opener work plus welding time if the posts need correction. We’ll quote the whole job in writing before anything starts.
It can be either one, or both. When the concrete apron settles, the rack and pinion bind and the plastic drive gear inside the operator strips, which makes the gate stall mid-travel. A misaligned loop detector can also send a false “vehicle present” signal that halts the gate. We diagnose both on site and quote the repair separately: a loop detector re-set typically runs $120 – $200, while rack re-alignment and gear replacement runs $240 – $480. Call (682) 432-9830 and we’ll tell you which failure you’re actually dealing with.
Entrapment protection is required for every automated gate, not just new installs. If your older Haltom City opener lacks working photocells or reversing edges, the gate is a serious safety hazard and a code violation. We restore the safety inputs on legacy operators whenever possible, and if the old board can’t support them, we’ll quote a replacement that can. This is not an upsell, it’s a safety requirement we won’t skip.
The hinge post first. A sagging iron gate panel usually owes to a post that has leaned under load, not a weak panel. If the post footing has shifted, tightening hinges or adding a wheel only masks the problem. We’ll assess the post base, then either re-set the post in a reinforced footing or cut and re-weld the hinge brackets. The panel usually goes back into true once the post is corrected. Call (682) 432-9830 for a free estimate, and we’ll tell you which approach your gate actually needs.
Written by Nico Alvarez, Owner at Calder Gate Repair Fort Worth, serving Haltom City gate opener repair needs with written pricing on every job.