Gate Repair Cost in Fort Worth - Honest Price Ranges, Free Written Quote

How Much Does Gate Repair Cost in Fort Worth?

Gate repair in Fort Worth typically costs between $180 and $750, with most homeowners paying around $340 for a standard opener or hinge repair. Simple fixes like sensor realignment or limit switch replacement run $120 to $250, while full opener replacement on a double driveway gate can reach $1,800 to $3,200 including the new motor and labor. Calder Gate Repair Fort Worth gives every customer a written price before any our Gate Repair services work starts, so the number you agree to is the number you pay.

Here’s what you need to know before calling: the biggest cost drivers are the type of opener you have (swing vs. slide), whether the gate is single or double leaf, and whether the problem is mechanical (hinges, wheels, chains) or electrical (control boards, motors, sensors). Fort Worth’s clay soil also plays a role we’ll get into below – it shifts more than most people realize, and that movement stresses gate frames and alignment.

Gate Repair Cost Breakdown (2026)

We work on gates across Fort Worth every day, from the older wrought-iron gates in Ridglea Hills to the newer steel and aluminum installs in Walsh Ranch and Alliance. The table below reflects what we’re actually quoting and invoicing in this market in 2026, not national averages that don’t account for Texas labor rates and the specific brands common in DFW.

Repair Type	Typical Cost Range (Fort Worth, 2026)	What It Includes
Limit switch adjustment or replacement	$120 – $250	The small sensor that tells the gate when to stop. Includes calibration and testing.
Photo eye / safety sensor realignment	$90 – $180	Cleaning, repositioning, and testing the beam that prevents the gate from closing on a car or person.
Hinge replacement (single gate)	$180 – $380	Heavy-duty weld-on or bolt-on hinges, gate removal and re-hang, alignment check.
Hinge replacement (double gate)	$320 – $650	Both leaves, including shimming to correct sag from Fort Worth’s shifting soil.
Opener motor replacement (single gate)	$450 – $900	New motor, gear assembly, and programming. Brand-dependent (see below).
Opener motor replacement (double gate)	$700 – $1,400	Heavier-duty motor required for two-leaf swing or slide gates.
Control board replacement	$280 – $650	Includes diagnosing the fried board, installing a compatible replacement, and reprogramming remotes and keypads.
Track wheel / v-wheel replacement (slide gate)	$150 – $325	Replacing worn rollers that cause the gate to drag or bind on the track.
Chain or belt replacement	$140 – $300	New drive chain or belt, tension adjustment, lubrication.
Full opener replacement (including new motor, arms, and remotes)	$1,800 – $3,200	Complete system swap for a double gate. Price depends on brand (LiftMaster and FAAC on the higher end, Mighty Mule and Ghost Controls on the lower end).
Emergency service call (after hours or weekend)	$95 – $180 trip fee + repair cost	Fort Worth-wide dispatch. A live person answers, day or night.

What drives the price up: A double gate needs heavier-duty openers, more hardware, and roughly twice the alignment work. A slide gate that’s dragging often means track damage, not just wheel replacement. And if your opener is a DoorKing or FAAC, parts cost more than entry-level Mighty Mule or Ghost Controls components – but those premium brands also tend to last 10 to 15 years with proper maintenance, so the math works out over time.

What drives the price down: Single-leaf gates, standard steel construction (no custom ornamental work), and brand-common parts that our techs stock on the truck. If you’re in an HOA community like Mira Vista or Montserrat, your gate’s brand and model are probably well-documented, which speeds up diagnosis.

What Affects Gate Repair Pricing in Fort Worth

• Gate type and weight. A 14-foot slide gate weighs more than a 6-foot swing gate. Weight determines motor size, hinge capacity, and how long the job takes. Ornamental iron gates from the 1990s in Arlington Heights are often heavier than they look.
• Swing vs. slide mechanism. Swing gates use an arm-and-motor setup that’s generally cheaper to repair. Slide gates run on tracks and rollers that collect debris, clay dust, and the occasional pebble from Fort Worth’s rocky soil, which wears components faster.
• Brand of opener. LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule all have different parts pricing and availability. Our techs are factory-familiar with all nine, so we usually diagnose the exact board or module failure on the first visit instead of guessing.
• Soil movement in Fort Worth. This is the local factor most people don’t expect. North Texas has expansive clay soil that swells when wet and contracts in drought. That movement shifts gate posts out of true over time, which puts stress on hinges, opener arms, and latch alignment. In neighborhoods like Wedgwood and Summer Creek, we regularly see gate sag from soil movement even when the hardware itself is fine.
• Age of the existing installation. Gates installed before 2010 often lack modern safety sensors and use opener models that are no longer manufactured. Retrofitting a new opener onto an old gate frame sometimes requires custom brackets and welding, adding $100 to $250 to the job.
• Access and site conditions. A gate at the back of a long driveway in Eagle Mountain takes more time to reach than a front-entry gate. If the gate is off its track and blocking access, we may need to stabilize it before repair work begins – that’s part of what the trip fee covers when we give you the quote.

Common Gate Problems and What They Cost to Fix in Fort Worth

Gate Won’t Open or Close

This is the call we get most often. In Fort Worth, the cause is usually one of three things: a failed capacitor in the opener (common after power surges during spring storm season), a limit switch that’s drifted out of adjustment, or a gear assembly that’s stripped. Capacitor replacement runs $80 to $150. Limit switch repair is $120 to $250. A stripped gear assembly inside a LiftMaster or FAAC opener typically costs $200 to $400 in parts and labor. If the control board is fried, expect $280 to $650 depending on the brand – Ghost Controls and Mighty Mule boards are on the lower end, DoorKing and Linear boards on the higher end.

Gate Is Sagging or Dragging

Sagging gates in Fort Worth are almost always a combination of Hinge & Post Repair needs and soil movement. A single hinge replacement runs $180 to $380; both hinges on a double gate run $320 to $650. If the gate is dragging on concrete, the fix may be wheel replacement on a slide gate ($150 to $325) or simply re-hanging and shimming the leaf on a swing gate. We include alignment testing with every hinge job because a gate that’s out of level will chew through its next set of hinges faster – and our 365-Day Done Right Promise means if the gate sags again within a year, we return at no charge.

Gate Opens Partially Then Stops or Reverses

This usually points to a safety sensor problem or a binding track. Photo eye realignment is $90 to $180 and takes about 30 minutes. If the gate reverses because the track is binding, the cost depends on whether the track needs cleaning and lubrication ($75 to $120) or wheel and track replacement ($150 to $325). The safety sensors themselves, if they need replacing, run $60 to $140 per pair.

Remote or Keypad Not Working

Before you assume the opener is dead, check the obvious: batteries, then the Lock Repair keypad code. If those aren’t it, a receiver board replacement runs $150 to $350. Reprogramming remotes and keypads is usually included with board replacement, and we test every remote and the keypad before we leave. For older LiftMaster and Linear systems, we can often source compatible remotes same-day from local Fort Worth suppliers.

Gate Makes Grinding or Squealing Noises

Grinding usually means gear wear inside the opener arm – $200 to $400 for a gear assembly replacement. Squealing from the hinge area is often fixed with cleaning and re-lubrication ($75 to $120), though severely worn hinge bearings need replacement ($180 to $380). If the noise is coming from the track, wheel replacement is the typical fix at $150 to $325. Ignoring the noise costs more later – a seized wheel can bend a track, and track replacement runs $400 to $800.

Brand-Specific Pricing in the Fort Worth Market

Fort Worth has a mix of gate brands, but we see certain ones more in certain areas. The newer master-planned communities around Chisholm Trail Parkway lean toward LiftMaster and Ghost Controls. Older established neighborhoods like Tanglewood and Berkeley Place have more FAAC, Linear, and DoorKing systems that were installed 10 to 20 years ago. Here’s what you can expect by brand:

• LiftMaster: The most common brand in DFW. Parts are readily available locally, which keeps labor costs down. Full opener replacement: $600 to $1,400. Control board: $280 to $550.
• FAAC: Premium Italian brand common on higher-end Fort Worth properties. Parts are pricier but long-lived. Opener replacement: $1,200 to $2,800. Control board: $400 to $650.
• Ghost Controls: Popular for DIY-friendly installs, but we fix a lot of them because the factory default settings aren’t always dialed in for heavy Texas gates. Opener replacement: $500 to $1,100. Control board: $200 to $400.
• Mighty Mule: Budget-friendly and common on single farm and ranch gates in areas like Benbrook and along the I-20 corridor. Opener replacement: $350 to $800. Control board: $150 to $300.
• DoorKing: Common on large slide gates at Fort Worth apartment complexes and commercial properties. The residential slide gate units are tanks. Opener replacement: $900 to $2,200. Control board: $350 to $650.
• Linear, Viking, BFT, Elite: Less common in Fort Worth residential settings but present on older installs and some newer luxury builds. Parts availability varies, which affects both price and timeline. We’ll always quote the full job before ordering anything.

Our techs carry common LiftMaster, Ghost Controls, and Mighty Mule parts on the truck, which means same-day repairs for a lot of Fort Worth calls. For FAAC, DoorKing, and Linear parts, we typically source from Dallas-area distributors same-day or next-day.

Fort Worth-Specific Considerations for Gate Repair

If you’ve lived in Fort Worth through a full summer, you know our clay soil doesn’t stay put. It expands after spring rains and contracts hard during August heat. That movement is the single biggest local factor in gate misalignment. We see it most in neighborhoods built on heavy clay, like Wedgwood, Meadowbrook, and the areas east of Loop 820. Gates that swung smoothly in April can start binding by July simply because the post shifted a half inch. The fix is usually re-shimming the hinge or adjusting the opener arm, not replacing the whole gate – but ignoring it will eventually crack welds and tear hinge bolts.

Heat is the other local variable. Fort Worth regularly hits 100+ degrees from June through September, and opener motors mounted in direct sun can overheat and shut down temporarily. If your gate stops working on a hot afternoon but works fine in the morning, that’s a heat-triggered thermal cutoff. We can add ventilation or relocate the control board to a shaded enclosure, typically $100 to $200 in labor.

Storm season also wreaks havoc on gate electronics. Lightning strikes and power surges between March and June are a common cause of fried control boards. If your gate stopped after a storm, pull the main power disconnect until we can inspect it – a half-fried board can cause intermittent behavior that’s hard to diagnose and may damage a new opener if it’s installed without addressing the surge damage. That kind of thorough diagnosis before any work begins is standard on every Calder call.

How to Save on Gate Repair in Fort Worth

The most reliable way to keep gate repair costs low is to catch small problems before they become big ones. Here’s what actually works:

• Lubricate hinges and chains twice a year. Spring and fall, right when Fort Worth temperatures shift. Use a silicone-based lubricant on hinges and a specific chain lube on chains. This $10 habit prevents $300 hinge replacements.
• Keep the track clear. If you have a slide gate, sweep the track monthly. Gravel, mulch, and clay clods get kicked onto tracks by lawn crews and will wear wheels and bend track guides.
• Test your safety sensors monthly. Wave your hand through the beam while the gate is closing. If it doesn’t reverse, the sensor is misaligned or failing. A $90 alignment call is cheaper than a $400 track repair from a gate that closed on something it shouldn’t have.
• Fix the sag early. A gate that’s dragging by half an inch can often be corrected with shims and an alignment tune-up ($150 to $250). Wait until it’s dragging by two inches and you’re looking at hinge replacement ($180 to $650).
• Ask for the written quote before work starts. Calder Gate Repair Fort Worth provides a written price on every job before turning a single bolt. That’s not an add-on; it’s standard. If a contractor won’t put the number in writing before starting, walk away.

The other way to save: call for a free estimate at (682) 432-9830. We’ll ask a few questions about your gate, get photos if you have them, and give you a realistic price range for the likely fix before we even send a truck.

Repair vs. Replace: How to Know Which One Makes Sense

Gate openers last 8 to 15 years depending on brand, usage, and how much Fort Worth sun they’ve absorbed. A good rule of thumb: if the repair cost is more than half the cost of a new opener, replacement is usually the smarter long-term call.

Here’s the breakdown by scenario:

• Opener under 5 years old: Repair is almost always the right call. Parts are still in production and the fix is usually a single component. $150 to $400 typical.
• Opener 5 to 10 years old: Borderline. If it’s a LiftMaster, FAAC, or DoorKing with a healthy motor, repair at $300 to $600 makes sense. If it’s a Mighty Mule or Ghost Controls with multiple worn components, replacing at $500 to $1,100 is often cheaper over the next 5 years.
• Opener over 10 years old: Replacement makes sense unless the fix is simple (<$200). New openers have better safety features and are compatible with smartphone controls, which matters if you're running a rental property or have frequent deliveries.
• Gate frame is damaged or rusted through: No repair will hold. Budget $1,500 to $4,000 for gate fabrication in Fort Worth, depending on size, material, and ornamental detail.

Nico Alvarez, owner at Calder Gate Repair Fort Worth, walks through this decision with every customer before any work is quoted. You’ll get a straight recommendation based on the age and condition of your equipment, not a sales pitch for a replacement you don’t need.

How the Calder Gate Repair Process Works in Fort Worth

Step 1: Call and Describe the Problem

Call (682) 432-9830. A live human answers, 24/7. No voicemail, no chatbot. We’ll ask what you’re seeing: Is the gate dead? Grinding? Opening halfway? Does the remote work but the keypad doesn’t? These details help us send the right tech with the right parts the first time.

Step 2: Get Your Trackable Arrival Time

Once booked, you get a live arrival time you can track from your phone. The Relay Standard is how we run every visit: a specific arrival window, a uniformed technician, and a text update when we’re en route. No vague four-hour windows.

Step 3: Diagnosis With a Written Price

The tech diagnoses the issue, explains exactly what’s wrong in plain language, and hands you a written price before any work begins. If the job needs a part we don’t have on the truck, we’ll source it and confirm the final price before ordering anything. The number on the invoice is the number you agreed to. Always.

Step 4: Repair and Verification

We complete the repair, run the gate through full open/close cycles, test the safety reversal, verify all remotes and keypads, and take before-and-after photos. You get a digital invoice you can pay from a link – no paper shuffling, no phone-tag follow-ups.

Step 5: The 365-Day Done Right Promise

Every repair from Calder Gate Repair carries a written 365-Day Done Right Promise. If the repair fails within 365 days for any reason related to our work or the part we installed, we return and fix it at no charge. That’s not a promotional gimmick; it’s written on every invoice. A second visit may be free, but it’s rare because we diagnose thoroughly before we repair.

FAQs – Gate Repair Cost in Fort Worth

How much does it cost to repair a gate opener in Fort Worth?

A gate opener repair in Fort Worth typically costs $180 to $750. The exact number depends on whether it’s a limit switch ($120 – $250), a gear assembly ($200 – $400), or a full motor replacement ($450 – $1,400 for a single gate, more for a double). Call (682) 432-9830 for a free estimate with a written price before any work starts.

Is it cheaper to repair or replace a gate opener?

If the opener is under 10 years old and the repair is $400 or less, repair is usually cheaper. If the opener is over 10 years old and the quote exceeds half the cost of a new opener ($600 to $1,400 installed for most brands in Fort Worth), replacement is the better long-term spend. We’ll give you a straight recommendation either way.

Can you fix my gate the same day in Fort Worth?

In most cases, yes. Common parts for LiftMaster, Ghost Controls, and Mighty Mule are stocked on our trucks, and our Fort Worth service area spans neighborhoods from Benbrook to Alliance. Call (682) 432-9830 and a live person will tell you if same-day is possible for your zip code.

Why does my gate keep going off track in Fort Worth?

Fort Worth’s expansive clay soil is the usual culprit. Post movement from seasonal soil expansion and contraction pushes the gate out of alignment, which makes it ride up on the track or bind at the hinges. A realignment and re-shim typically costs $150 to $350. Replacing worn track wheels that the misalignment destroyed adds $150 to $325.

How much does emergency gate repair cost in Fort Worth?

Gate Repair Near Me in Fort Worth, TX emergency service runs a $95 to $180 trip fee plus the repair itself. A 24/7 live person answers every call, so if your gate is stuck open at 11 p.m. in Riverside or stuck closed in Ryan Place, you’ll talk to a human who can dispatch a tech. The trip fee is included in the written quote you get before we start.

Do you charge for estimates?

No. Estimates are free. Call (682) 432-9830, describe your gate issue, and we’ll give you a realistic price range before scheduling. The written quote at your door is the final price – no surprises.

Key Takeaways

• Most gate repairs in Fort Worth cost $180 to $750, with simple fixes like sensor realignment at the low end and opener replacements at the high end.
• Fort Worth’s clay soil movement and extreme summer heat are the two local factors that most affect gate alignment and opener reliability.
• Calder Gate Repair provides a written price before any work starts and backs every repair with the 365-Day Done Right Promise: if the fix fails within a year, we return free.
• A live person answers (682) 432-9830 24/7 – no voicemail, no chatbot.
• We’re factory-familiar with LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.

Get a Free Gate Repair Estimate in Fort Worth

If your gate is acting up – stuck open, grinding, refusing to close, or dead after a storm – call Calder Gate Repair Fort Worth at (682) 432-9830. You’ll get a live person, a straight answer on cost, and a written price before any work begins. We’re part of the Relay Home Co. family, founded in 2009, and every tech who rolls up to your Fort Worth property is background-checked, uniformed, and arrives with a trackable time. Free estimates, upfront pricing, and a repair that’s done right the first time or we come back free.

Pricing reflects the Fort Worth market as of 2026. Calder Gate Repair Fort Worth offers free estimates – call (682) 432-9830.