Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Motor & Opener Cost in Fort Worth?
Gate motor and opener replacement in Fort Worth typically runs $650 to $1,800 for the unit and installation on most residential swing or slide gates. Repairs land lower, usually $150 to $450 before parts, with the most common fixes (limit switch adjustments, capacitor swaps, receiver board replacements) clustering under $300. Heavy-duty commercial openers or long slide gates in areas like Walsh Ranch or Montserrat can push past $2,800, but that’s the exception, not the rule.
This guide breaks down what you’ll actually pay in the Fort Worth market in 2026, line by line, so you know the number before you call. Calder Gate Repair Fort Worth writes the price down before any work starts, so there’s no door-knock surprise.
Gate Motor & Opener Cost Breakdown (2026)
Here’s what we’re quoting across Fort Worth neighborhoods right now. These are real ranges from jobs in places like Benbrook, Saginaw, Lake Worth, and the Near Southside, updated for 2026 parts pricing.
| Item | Typical Fort Worth Price Range | Notes |
|---|---|---|
| Residential swing gate opener (single arm) | $650 – $1,200 installed | Mighty Mule, Ghost Controls, LiftMaster LA400/412 |
| Residential slide gate opener | $900 – $1,800 installed | LiftMaster SL3000, Linear, BFT Deimos |
| Commercial slide gate opener | $1,800 – $3,200 installed | FAAC 844, Viking, DoorKing 9100 |
| Opener motor only (no install) | $250 – $700 | Depends on brand and horsepower |
| Control board replacement | $180 – $420 installed | DoorKing and FAAC boards run higher |
| Limit switch replacement or adjustment | $90 – $180 | Most common repair we do |
| Photo eye / safety sensor replacement | $120 – $260 per pair | Required for code compliance |
| Remote / keypad programming | $60 – $140 | Includes new remote if needed |
| Diagnostic service call | $75 – $110 | Waived when you approve the repair |
Three things move the needle most on price in Fort Worth: gate type (swing vs. slide), horsepower, and whether the opener arm or rack needs replacing along with the motor. A swing gate opener costs less because the mechanism is simpler. Slide gates need a steel rack or chain run along the gate’s length, and that adds $300 to $700 in parts alone on a 20-foot gate.
Parts scarcity also matters in 2026. Some FAAC and Viking control boards are still on extended lead times, which pushes rush-install pricing up. Calder Gate Repair keeps inventory on hand for the nine brands we service daily: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. If we have the board on the truck, you’re not paying a markup for a two-day air freight order.
What Affects Gate Motor & Opener Pricing in Fort Worth
- Gate type and weight. A 400-pound ornamental iron swing gate needs a beefier opener than a lightweight tube-steel gate. Fort Worth’s older neighborhoods, like Crestwood and Berkeley Place, often have heavy custom iron gates that demand a 1/2 HP motor minimum, adding $150 to $300 over a light-duty unit.
- Slide gate track and rack condition. If the steel rack is worn or the track is pitted from years of North Texas weather, the new opener will fail early. We quote rack replacement at $25 to $40 per linear foot in Fort Worth. Skipping it because the old rack “looks okay” is the most common cause of a second repair call.
- Soil movement. Fort Worth sits on expansive clay. Gate posts in neighborhoods like Wedgwood and Como shift after dry summers, throwing the gate out of alignment. A gate that drags or binds puts extra strain on the opener, and sometimes the post reset ($250 to $500) has to happen before the motor replacement. We see this pattern every year after a hot July.
- Electrical access. If there’s no dedicated outlet at the gate, you need a new circuit run. Depending on distance from the panel, that’s $300 to $800 in Fort Worth for a licensed electrician’s work, coordinated through our team.
- Brand and parts availability. LiftMaster and Mighty Mule parts are volume-priced and easy to source. FAAC and Viking are premium commercial brands with higher component costs. A Viking control board runs $280 to $450 for the part alone; a Mighty Mule board is often half that.
- Access control integration. Adding a keypad, phone app module, or HOA gate code integration tacks on $150 to $500 depending on what your community’s system requires. HOA-governed neighborhoods around Benbrook Lake and Tanglewood often have specific opener models in their deed restrictions.
For a fuller picture of how these factors play out on service calls, see our Gate Motor & Opener in Fort Worth guide.
Repair vs. Replace: What Makes Sense In Fort Worth
The general rule we use: if the opener is under 8 years old and the repair is under half the cost of a new unit, fix it. If the opener is over 10 years old or the repair estimate crosses the 50% line, replacement usually saves money over the next two years.
Here’s the math from a real Fort Worth example. Last month in Lake Worth, a homeowner had a 2009-era LiftMaster with a seized motor and a corroded mainboard. Repair quote came in at $780. A new LiftMaster LA412 with a 365-Day Done Right Promise and a written guarantee ran $1,050 installed. The customer chose replacement because the old unit had already failed twice in three years. That’s the common pattern: patch-fixes on aging openers cost more per year than a clean replacement.
Calder Gate Repair includes a written price before any work starts on both repair and replacement, so you can make that call with real numbers in front of you, not a technician’s verbal shrug.
How to Save on Gate Motor & Opener in Fort Worth
You don’t need to nickel-and-dime a technician to get a fair price. You need to time the work, size the unit correctly, and skip unnecessary upgrades.
- Replace the opener before it fully seizes. When a motor starts struggling, grinding, or tripping the breaker, the repair is cheaper before the failure cascades to the control board and gear train. Waiting until total failure often doubles the parts list.
- Bundle the maintenance. If the opener needs a board and the gate hinges have never been greased, ask for a service tune-up ($89 to $130) while the technician is already there. You save the separate trip fee, and the opener runs with less strain, which extends its life.
- Don’t overbuy horsepower. A 1/2 HP opener is right for most residential swing gates under 16 feet and 600 pounds. You don’t need a 1 HP commercial unit for a driveway gate, and the price difference runs $300 to $700.
- Take the free estimate. Calder Gate Repair Fort Worth gives a written estimate before any work starts. Call (682) 432-9830, describe your gate and opener brand, and we’ll get you a number. No fee, no obligation.
- Buy the right brand the first time. Short-term, a cheap off-brand unit saves $150. Over five years in Fort Worth heat and clay-shift conditions, you’ll replace it twice. Stick with LiftMaster, Mighty Mule, Ghost Controls, or other brands with local parts availability.
What a Gate Motor Replacement Involves, Step by Step
Here’s the exact sequence our technicians follow on a replacement job in Fort Worth. This is what the $650 to $1,800 covers.
- On-site assessment (free): The technician checks gate weight, travel, post stability, and existing wiring. You get a written quote with parts and labor separated. The number on the quote is the number on the invoice.
- Removal of the old opener: We disconnect power, remove the old arm or chain drive, and inspect the gate hinge bearings and slide track for wear that would shorten the new opener’s life.
- Mounting the new opener: The new unit is mounted at the correct height and angle for the gate’s geometry. On slide gates, we install or reuse the rack with attention to tooth engagement. Poor rack alignment is the top cause of early slide-opener failure.
- Electrical connection and safety sensor setup: The opener is wired to a dedicated GFCI circuit. Photo eyes are installed at the required heights (UL 325 compliance), and the entrapment sensor is tested before we leave.
- Limit and force adjustment: The limit switch, the small sensor that tells the gate when to stop, is set so the gate closes fully without slamming. Force settings are dialed back to the minimum that moves the gate consistently.
- Remote and keypad programming: We program remotes, keypad codes, and app access if your opener supports it. You get a demo before we pack up.
- Paperwork and warranty: You receive the written 365-Day Done Right Promise, a digital invoice you can pay from a link, and before-and-after photos. If anything fails within 365 days, Calder comes back at no charge. That trigger, that term, that outcome, in writing.
FAQs – Gate Motor & Opener Cost in Fort Worth
How much does it cost to replace a gate opener motor in Fort Worth?
Replacing just the motor on a swing gate opener runs $250 to $700 for parts, with labor adding $150 to $300. On slide gates, motor replacement lands between $400 and $800 in parts because the motor assembly is integrated with the gearbox. If your opener is a sealed-unit design, the motor may not be separately replaceable, and you’re looking at a full unit swap at the $650 to $1,800 range. Call (682) 432-9830 for an exact quote, we’ll give you the written number before anything starts.
Is it cheaper to repair or replace a gate opener in Fort Worth?
Repairs under $350 on an opener less than 8 years old are almost always cheaper than replacement. Once the quote passes the $500 mark on a unit that’s 10 years or older, replacement starts to make more sense because the next component failure is usually not far behind. We give you both numbers on site, in writing, and you decide with full information.
How much does a swing gate opener cost in Fort Worth?
A residential swing gate opener installed in Fort Worth costs $650 to $1,200 for most single-family gates. The opener unit itself is $350 to $700 depending on brand and horsepower, and installation labor runs $300 to $500. Heavy custom iron gates can push the total to $1,400 because a stronger arm and reinforced post bracket are required.
How much does a slide gate opener cost in Fort Worth?
A residential slide gate opener installed in Fort Worth costs $900 to $1,800. The motor unit itself runs $500 to $1,000, and the installation includes rack mounting, track alignment, and sensor setup. If the existing rack needs replacement, add $25 to $40 per linear foot. Commercial slide gate jobs in Fort Worth typically run $1,800 to $3,200 installed.
Can you replace a gate opener the same day in Fort Worth?
Yes, in most cases. Calder Gate Repair Fort Worth keeps common LiftMaster, Mighty Mule, Ghost Controls, and FAAC units stocked locally. If we have your opener on the truck or at our Fort Worth supply bench, same-day replacement is doable. A live person answers the phone 24/7 at (682) 432-9830, so call and we’ll tell you straight whether today works.
Does Fort Worth require a permit for gate opener installation?
For most residential single-family gate openers, the City of Fort Worth does not require a standalone permit for the opener itself. However, if the installation includes a new electrical circuit run from the panel, that electrical work must be done by a licensed electrician and may require a permit depending on the scope. We coordinate the electrical portion through licensed contractors and handle the paperwork when it applies.
Why did my gate opener stop working after a Fort Worth thunderstorm?
North Texas storms bring lightning strikes and power surges that commonly fry control boards and low-voltage transformers. We replace storm-damaged control boards in Fort Worth for $180 to $420 installed depending on the brand. If your opener is dead after a storm, don’t force the gate manually against the motor, turn off the breaker and call us. A technician can diagnose the exact failed component and give you a written repair quote on the spot.
Contact Calder Gate Repair Fort Worth
Calder Gate Repair is the dedicated gate repair specialist inside the home network, and every job carries the Relay Visibility Guarantee: a live, trackable arrival time, a written price before work starts, before-and-after photos, and a digital invoice you pay from a link. No four-hour window. No door-knock repricing.
Our technicians are background-checked, uniformed, and factory-familiar with LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Nico Alvarez leads the Fort Worth team, and every repair or replacement is covered by the 365-Day Done Right Promise: if the repair fails within 365 days, Calder returns at no charge. It’s in writing on every job.
Call (682) 432-9830 for a free estimate. A live person answers, 24/7, not a voicemail. We’ll give you a real number before any work starts.
Pricing reflects the Fort Worth market as of 2026. Calder Gate Repair Fort Worth offers free estimates – call (682) 432-9830.
Written by Nico Alvarez, Owner at Calder Gate Repair Fort Worth, serving Fort Worth since 2009.
What Our Customers Say
"Slide gate wheels replaced. Glides smoothly now."
- Mark T."Booked online. The tech texted his ETA and arrived on time. Gate opener was dead; he replaced the control board and tested the sensors."
- Terry W."Safety sensors realigned. Works fine. Photo eyes were dirty and out of line. Gate now stops when it should."
- Raul A.