FAAC Electric Gate Repair Nationwide

FAAC Electric Gate Repair in Fort Worth: What to Know First

FAAC electric gate repair in Fort Worth typically runs $185 – $420 for most opener and control board issues, with same-day or next-day service available in most cases. We’re an independent FAAC service provider, not a factory dealer, which means we fix what’s actually broken instead of selling you a replacement you don’t need. If your FAAC gate is doing something it shouldn’t, call Calder Gate Repair Fort Worth at (682) 432-9830 and we’ll walk you through what we’re likely looking at over the phone before we even roll a truck.

Call (682) 432-9830

This page is for FAAC owners in Fort Worth who want straight answers: what breaks on these openers, what it costs to fix, and what the repair process actually looks like from your driveway. No jargon runs, no vague estimates.

How FAAC Products Fail – and How We Fix Them

FAAC builds solid hydraulic and electromechanical openers, but every brand has its patterns. Here’s what we see most often on FAAC gates across Fort Worth neighborhoods like Summerfields, Tanglewood, and Arlington Heights:

• Control board relay failure on C720 and C721 series. The FAAC C720 and C721 control boards use small relays that wear out after years of cycling, especially in Texas heat. The symptom is a gate that works fine for a week, then won’t move at all until someone taps the cabinet. We test the relay in place, and if it’s failing, we replace it with a quality relay rated for the load rather than upsell a whole new board.
• Limit switch drift on FAAC 400 series swing operators. The FAAC 400 and 412 operators use mechanical limit switches that slowly drift out of adjustment as the cam lobes wear. Your gate might start closing short of the post, or over-travel and slam the stop. We re-time the cams and switches, then verify the gate hits both limits cleanly through 10 full cycles.
• Hydraulic fluid leaks on FAAC 750 and 844 gearboxes. FAAC’s hydraulic swing operators are tough, but seals harden and crack after 8 to 12 years in Fort Worth’s summer heat. A slow weep near the cylinder base is the tell. We replace the seal kit, refill with the correct FAAC-spec hydraulic fluid, and pressure-test the circuit. That’s usually a fraction of what a new operator costs.
• Keypad and receiver interference on FAAC 391 and 455D systems. FAAC’s older 455D receiver modules are notoriously picky about antenna placement. If your remote only works from 10 feet away, or the keypad flashes but the gate doesn’t respond, the issue is often signal degradation, not the remote battery. We test the receiver output directly and relocate or replace the antenna as needed.
• Capacitor failure on single-phase FAAC motors. FAAC 750 and 770 operators with single-phase motors use a start capacitor that degrades in heat. The motor hums but won’t turn, or the gate moves sluggishly and trips the thermal overload. A capacitor is a $40 to $80 part, and it takes about 20 minutes to swap. It’s one of the most common “dead gate” fixes we do on FAAC systems in Fort Worth.

Our FAAC Electric Gate Repair Process

1. 1
   You call, a live person answers. 24/7, no phone tree. You describe what the gate is doing or not doing, and we give you a straight read on what it’s likely to be.
2. 2
   We send a tech with a live arrival time. Background-checked, in uniform, and you can track the truck on your phone. No four-hour windows.
3. 3
   Diagnostics on site. We open the operator, test voltages, check limit switches, inspect the control board, and confirm the exact failure. Nico Alvarez grew up learning this trade in LA and has been diagnosing FAAC systems in Fort Worth for years, so we don’t do the “replace parts until it works” routine.
4. 4
   You get a written price before any work starts. Parts and labor, line by line. If we think OEM FAAC parts make sense, we say so. If a quality aftermarket part does the same job for less, we say that too. The number on the estimate is the number on the invoice.
5. 5
   We fix it, test it hard, and document it. We run 10+ full cycles, test safety sensors and remotes, and verify the gate stops where it should. You get before-and-after photos and a digital invoice you can pay from a link.
6. 6
   The 365-Day Done Right Promise kicks in. If the repair fails within 365 days, we return at no charge. That’s in writing, on every job.

What FAAC Electric Gate Repair Costs in Fort Worth

Most FAAC electric gate repairs in Fort Worth land between $185 and $420 before parts. Here’s the breakdown by job type:

• Capacitor replacement: $120 – $180
• Limit switch adjustment or replacement: $140 – $240
• Control board repair (relay or solder work): $180 – $350
• Full control board replacement: $350 – $650 depending on model
• Hydraulic seal kit and fluid service: $280 – $480
• Photocell or safety sensor replacement: $160 – $260 per sensor

What moves the price: the age of the unit, whether the operator’s hydraulic or electromechanical, and whether OEM parts are still available for the model. We won’t quote a repair from the phone without seeing the unit, but we will give you a realistic range before we come out. The estimate at your gate is the price you pay. Nothing gets started until you approve it in writing.

Call (682) 432-9830 for a free estimate. We’ll tell you what we think it is, what it likely costs, and when we can get there.

Why Fort Worth Homeowners Call Calder Gate Repair Fort Worth for FAAC Work

We’re the gate repair specialist inside the Relay Home Co. family, which has been around since 2009. Every Calder Gate Repair Fort Worth job carries three things that aren’t optional: a written price before any work starts, a written guarantee on every repair, and a free second visit if the repair fails within the 365-Day Done Right Promise window. That’s The Relay Standard, and it applies to every FAAC job we do.

Our techs work on FAAC openers regularly, not occasionally. When a FAAC control board, limit switch, or hydraulic system acts up, we know the model-specific quirks and the fastest path to a solid fix. And if your FAAC unit is beyond saving, we’re also factory-familiar with LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so we can talk through replacement options without starting from zero.

FAQs