Before & After Gallery - Calder Gate Repair Fort Worth

Gate Repair Before & After in Fort Worth, TX

Talk is cheap when your gate is sagging on its hinges or refusing to open at 6 a.m. We could tell you our technicians are thorough, but it means more to show the actual work. Below are representative jobs from Fort Worth neighborhoods like Wedgwood, Ridglea Hills, and Ryan Place. Real gates, real problems, and the same 365-Day Done Right Promise we put in writing on every single job.

Call (682) 432-9830

Recent Transformations

Sagging Driveway Gate, Ryan Place

BeforeAfter

The gate had dropped over two inches at the latch side, which meant it dragged across the concrete every time the LoopMaster opener tried to move it. Our technician found the original weld at the top hinge had torn loose and the post had shifted slightly in the Fort Worth clay soil. We re-set the post, replaced both hinge assemblies, and re-welded the frame. The gate now clears the driveway by a full inch and the opener no longer strains on every cycle.

Dead LiftMaster Opener, Wedgwood

BeforeAfter

After a June thunderstorm rolled through, the keypad lit up but the gate wouldn’t budge. We traced it to a shorted control board inside the LiftMaster LA400, likely from a power surge. Rather than sell a whole new opener, we installed a replacement board, re-seated the limit switches – the small sensors that tell the gate when to stop – and ran a full open/close cycle test. Total time on site was just under two hours, and the gate has cycled cleanly ever since.

Broken Gate Wheel on a Sliding Gate, Ridglea Hills

BeforeAfter

A sliding gate that grinds instead of glides usually points to one culprit: a seized support wheel. This one had flat-spotted and cracked, which let the gate ride directly on the track and chew a groove into it. We replaced the wheel with a sealed-bearing unit rated for the gate’s weight, then dressed the track surface so the new wheel rolls smooth. The homeowner told us she can now open it with two fingers instead of both hands and a shoulder.

Ghost Controls Opener Stopped Mid-Travel, Fairmount

The gate would open about eighteen inches, shudder, and reverse itself. Classic limit switch failure on a Ghost Controls arm. These switches tell the motor exactly where to stop, and when they drift out of adjustment the opener gets confused and backs off. We replaced the switch, re-calibrated the travel distance, and verified the auto-close timer still worked. No new opener needed, just a sixty-five dollar part and a service call.

Rusted Pedestrian Gate Hinges, North Hi Mount

That rusted hinge didn’t get that way overnight, and by the time we arrived the gate had to be lifted to latch at all. Fort Worth’s humidity mixed with years of sprinkler overspray had eaten through the original hardware. We cut off the old hinges, welded on new heavy-duty barrel hinges, and re-hung the gate so it swings true. We also adjusted the spring closer so it no longer slams shut like a screen door in a windstorm.

FAAC Hydraulic Opener Leak, Rivercrest

Oil staining on the gate operator housing is never cosmetic. In this case a degraded O-ring on the FAAC hydraulic cylinder was letting fluid weep out, and eventually the gate would have lost enough pressure to stop moving altogether. We replaced the seal set, flushed the hydraulic lines, refilled with the correct fluid, and cycled the gate twenty times while watching for any residual seepage. The unit runs quiet and dry now, and the gate moves at the same speed it did when it was new.

Want Results Like These?

If your gate sags, grinds, buzzes, or simply won’t move, the fix is usually more straightforward than it looks. We’ll send a background-checked, uniformed technician to your Fort Worth home with a written price before any work begins. That price, plus the 365-Day Done Right Promise and a free second visit if the repair fails, is on paper before we touch a tool. Call (682) 432-9830 and talk to a live person, 24/7.

Written by Nico Alvarez, Owner at Calder Gate Repair Fort Worth, serving Fort Worth since 2009.