Linear Electric Gate Repair Nationwide

Linear Electric Gate Repair in Fort Worth: What to Know First

Linear electric gate repair in Fort Worth typically runs $180 to $340 for most opener and control board fixes, with same-day or next-day service available for most failures. We’re an independent Linear service provider, not a factory-authorized shop, which means we make parts and repair decisions based on what’s actually best for your gate and your budget, not what a manufacturer’s warranty portal requires. If your Linear gate won’t open, won’t close, or opens halfway and gives up, call Calder Gate Repair Fort Worth at (682) 432-9830, tell us what it’s doing, and we’ll give you a straight answer and a written price before anyone turns a wrench.

Call (682) 432-9830

How Linear Products Fail – and How We Fix Them

Linear has been building gate operators and accessories for decades, and in Fort Worth we see a handful of failure patterns repeat across the models installed in neighborhoods like Tanglewood, Wedgwood, and the Summerfields area. Here’s what actually breaks on Linear equipment:

• Linear APeX and LRA swing gate arms: capacitor failure after summer heat. Fort Worth’s consecutive 100-degree weeks cook the motor start capacitors inside older Linear swing arms. The gate hums but doesn’t move, or it moves two inches and stops. We test the capacitor under load, replace it with a higher-tolerance unit when the motor windings are still healthy, and check the arm’s limit switches while we’re in there. Most of these are same-visit fixes.
• Linear MegaCode receiver modules and remote “ghosting.” The MegaCode receiver bolted to the control box occasionally forgets remotes after a power surge or a lightning-close strike. Your remotes blink, the gate does nothing, and the keypad still works. We reprogram the receiver, replace the surge-damaged capacitor on the board if needed, and install a small surge protector on the low-voltage side so the next Texas thunderstorm doesn’t erase everything again.
• Linear slide gate chain and sprocket wear on the SL and SLR series. Slide gates in Fort Worth sit in dust and grit year-round. The drive chain on Linear SL operators stretches and the sprocket teeth wear down until the gate jerks, grinds, or loses its stop position. We measure chain sag, replace the chain and sprocket as a set when wear has gone past adjustment range, and re-set the close and open limits. A chain that’s slapping the guide rail is a chain you’ll be replacing soon anyway.
• Photocell and safety edge faults on Linear swing systems. A single misaligned photo eye or a cracked safety edge will tell the control board “something’s in the way” and stop the gate cold. Linear boards flash a diagnostic code, but the code just says “safety device fault” – it doesn’t tell you which one. We test the photo eyes, the edge, and the wiring runs separately to isolate the fault in minutes instead of guessing and replacing good parts.
• Control board relay burnout on older Linear models. The relay that fires the motor on pre-2015 Linear boards eventually welds or burns out, especially on gates cycling 40 or 50 times a day. The gate clicks but doesn’t move, or it keeps running after it should stop. We replace the relay or the whole board depending on age and condition, and we’ll tell you upfront which one makes sense for your equipment – never a mystery upsell.

The common thread with Linear is that the mechanical parts and motors are solid, but the peripherals – capacitors, relays, sensors, and receivers – take the abuse from heat, dust, and surges. That’s why our Linear calls in Fort Worth usually end up being two-hour repairs, not full replacements.

Our Linear Electric Gate Repair Process

Here’s exactly how a Linear repair goes when you call Calder Gate Repair Fort Worth:

1. 1
   You call, a person answers. No menu tree. You describe the symptom, and we ask a few pointed questions. “Tell me what it’s doing – or not doing – and I’ll tell you exactly what it needs.” That’s Nico’s line, and it’s how every call starts.
2. 2
   We quote the diagnostic honestly. The dispatch fee covers the tech’s time and the full diagnostic. If we fix it in the same visit – and we usually do – the diagnostic rolls into the repair total. You’ll hear the repair price before we start any work.
3. 3
   The tech arrives with the truck stocked for Linear. We carry Linear-compatible capacitors, relays, receiver modules, limit switches, photo eyes, and remotes, plus the multi-meter and load testers to verify the diagnosis instead of swapping parts on a hunch.
4. 4
   We decide OEM vs. aftermarket with you. Linear OEM parts cost more. Quality aftermarket equivalents – capacitors, remotes, photo eyes – are often half the price and work identically. What matters is the motor, the board, and safety components; we’ll install OEM or proven aftermarket depending on the part and your budget, and we’ll tell you the price difference before ordering anything.
5. 5
   We fix it, test it, and run a full cycle check. Ten or fifteen full open-close cycles, safety sensor interruption tests, force settings checked against the gate’s actual weight and wind load. You watch it work before we leave.
6. 6
   You get the written guarantee and a digital invoice. The 365-Day Done Right Promise is on every job in writing. If the repair fails within 365 days, we come back free. No fine print, no phone tag.

What Linear Electric Gate Repair Costs in Fort Worth

Here’s what we quote most often in Fort Worth, before tax:

• Capacitor replacement (Linear APeX / LRA swing arms): $120 – $185
• Diagnostic visit only (if you decline the repair): $89
• Remote programming or receiver module replacement: $95 – $225
• Photo eye or safety edge replacement: $145 – $280
• Control board repair (relay replacement): $180 – $320
• Control board replacement (new board): $320 – $550
• Chain and sprocket replacement (Linear SL / SLR slide gates): $260 – $460
• Full swing arm replacement (Linear APeX): $650 – $1,100

Your price depends on your exact Linear model, the parts it needs, and the condition of the gate itself – a gate that’s out of alignment will eat a new arm faster than the old one did, and we’ll flag that before we quote the arm. The price you agree to is the price you pay. Estimates are free when we’re already on site for the diagnostic; call (682) 432-9830 and we’ll give you a real number, not a “we’ll see when we get there.”

Why Fort Worth Homeowners Call Calder Gate Repair Fort Worth for Linear Work

We’re the gate repair specialist inside the Relay Home Co. family, founded in 2009. Every Calder Gate Repair Fort Worth job carries three promises that are absolute: a written price before any work starts, a written guarantee on every repair, and a free second visit if the repair fails within the 365-Day Done Right Promise window. A real person answers our phones 24/7 – not a chat bot, not a voicemail. Every tech is background-checked, wears a uniform, and arrives on a live, trackable ETA, not a four-hour window. Nico and his crew cut their teeth on the gate openers across the Southwest, and Fort Worth gets the sharp end of that experience. We service all the major brands – LiftMaster, Mighty Mule, Ghost Controls, DoorKing – so if your Linear board is beyond saving, we’ll talk you through every option before you spend a dollar.

Linear Electric Gate Repair FAQs