Linear Gate Repair Nationwide

Linear Gate Repair in Fort Worth: What to Know First

Linear gate repair in Fort Worth typically runs $145 – $385 for most opener and control-board fixes, with hinge, post, and weld work priced separately after an on-site look. We’re an independent Linear service provider, not an authorized dealer, and we carry the parts and diagnostics to get most systems running same-day or next-day. You’ll always get a written price before any work starts.

Call (682) 432-9830

This page is for Fort Worth homeowners and property managers with a Linear opener that’s acting up: gate won’t open, remote stopped working, motor hums but nothing moves, or the gate reversed mid-travel and now sits dead. If that’s you, call (682) 432-9830 and describe what you’re seeing. A live person answers, and we’ll give you a straight read on what it probably is and what it’ll take to fix.

Key Takeaways:

• Most Linear board and arm repairs run $145 – $385 before parts; full replacement arms or new control boards land higher.
• We service Linear swing and slide gate operators, including legacy APeX, LDO, and older MegaCode series still turning up across Fort Worth.
• Every repair includes a written price upfront, a written guarantee, and a free second visit if the fix fails within 365 days.
• We also work on LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if the brand on your gate ends up being a mismatch, we’re already equipped.

How Linear Products Fail – and How We Fix Them

Linear built a reputation for dependable residential gate operators, especially through the APeX and MegaCode lines installed in large numbers around Tarrant County in the 2000s and 2010s. What we see most often in Fort Worth isn’t the motor itself dying; it’s the control environment around it. Here are the failure patterns we run into, and what we do about them.

• APeX controller board relay failure. The relay that sends voltage to the motor sticks or welds closed after years of cycling in Texas heat. Symptom: the gate opens fine but refuses to close, or you hear a faint click and nothing happens. Fix is board-level repair where possible, or a new APeX board matched to your arm’s revision number. A mismatched board revision can trigger phantom limit errors, so we match before we swap.
• LDO series limit switch drift. The limit switch, a small sensor that tells the gate where to stop, loosens or shifts over time on LDO swing arms. Symptom: the gate slams into the post and reverses, or stops three inches short of the latch. We re-set the limit and tighten the cam so it holds its position through a full Fort Worth summer.
• MegaCode receiver antenna corrosion. The short external antenna on older MegaCode receivers oxidizes, especially near sprinkler overspray, and your remote’s range drops from 40 feet to “must stand at the keypad.” We’ll remove the corroded connector, replace the antenna pigtail, and re-seal the housing. When we re-use the existing MegaCode remotes and keypad, the programming stays intact and you don’t buy new transmitters.
• Gearbox wear on Linear slide-gate operators. The drive gear inside older Linear slide units strips after years of pulling a heavy gate over a rough concrete track. Symptom: the motor spins, the gate doesn’t move, and you smell hot oil. We replace the gear with a compatible gear set and check the track rollers while we’re in there, because a drag from a bad roller kills a new gear within months.
• Solar-optimized Linear boards that aren’t getting solar input. Some Linear swing operators were installed with solar kits, and the charge controller fails quietly. Symptom: the gate works for three days after a sunny stretch, then dies after one cloudy morning. We test the panel output, replace the controller, and re-wire the battery bank if needed. The Fort Worth sun is plenty; the controller just has to actually pass it through.

Our Linear Gate Repair Process

You get a clear sequence from the first call to the final test, and you see the price before we touch a tool. Here’s how a typical Linear repair runs with us:

1. 1
   You call (682) 432-9830. A live person answers 24/7. You tell us what the gate is doing, or not doing, and we give you a likely cause and a realistic arrival window, not a four-hour “sometime today.”
2. 2
   We diagnose on-site. Nico or one of our techs tests the control board, limit settings, battery and motor draw with a meter. We find the actual fault, not the first guess.
3. 3
   You get a written price. Before any work begins, we hand you a line-item quote: parts, labor, and any track or hinge work the gate needs. The number you approve is the number you pay.
4. 4
   We repair using the right parts. For Linear jobs we prefer genuine Linear parts where the board is still supported; for discontinued components we use name-brand aftermarket parts with equal or better specs, and we tell you which we’re using before ordering.
5. 5
   We cycle-test the gate. The gate runs at least ten full open-close cycles with the vehicle sensor and safety edges in play. If it stumbles, we don’t pack up.
6. 6
   You get a written guarantee and digital invoice. The 365-Day Done Right Promise applies; if this repair fails inside a year, we come back at no charge. You get a digital invoice you can pay from a link, and before-and-after photos of the work.

What Linear Gate Repair Costs in Fort Worth

Repair pricing on Linear systems in Fort Worth breaks down by the part that actually failed. Here’s what we’re seeing on the ground in 2025, before any parts are ordered:

What moves the price: gate weight, how far the post has shifted, and whether the board is still a current Linear part number. We quote the repair, not a vague estimate, before you approve anything. Call (682) 432-9830 for an exact quote on your Linear system; estimates are free.

Why Fort Worth Homeowners Call Calder Gate Repair Fort Worth for Linear Work

We’re the gate repair shop inside the Relay Home Co. family, and we’ve been doing this long enough to know that a Linear board from 2008 and a Linear board from 2023 are not the same job. Our techs are trained on the quirks of the APeX and MegaCode lines specifically, and when a Fort Worth gate turns out to have a LiftMaster or Mighty Mule opener instead, which happens more than you’d think, we don’t blink. We service those too, along with Ghost Controls and DoorKing.

Every job carries the same three things in writing: a price before we start, a written guarantee on the repair, and a free second visit if it fails within 365 days. That’s the 365-Day Done Right Promise and it isn’t a marketing line; it’s the terms we hand you on paper. We dispatch background-checked techs in uniform with a live, trackable arrival time, and a real person picks up the phone around the clock. No voicemail tree. No chat bot. The Relay Standard is simple: you know who’s coming, when they’ll arrive, and what it’ll cost.

FAQs

Will repairing my Linear opener void the manufacturer warranty? No. As an independent Linear service provider, we don’t void warranties by working on your gate. If the system is still under Linear’s factory warranty, we’ll flag it before any paid repair and let you decide whether to file a claim with the manufacturer first.

Can you get parts for older Linear models that aren’t made anymore? We can in most cases. Discontinued Linear boards and gear sets are often available through supplier networks we use, and when they’re not, we install compatible aftermarket parts with matching specs and tell you that before ordering. Call (682) 432-9830 with your model number and we’ll check availability while you’re on the phone.

Is it better to repair my old Linear opener or replace it? If the repair is under about half the cost of a new opener and your gate and posts are sound, repair makes sense. When the board, gearbox, and arm all fail at once, or the unit is past about 15 years old, we’ll give you straight numbers for both paths and let you decide without pressure.

How fast can you get to my Fort Worth property for a Linear gate repair? In most cases we can have a tech out same-day or next-day, depending on where you are in Fort Worth and what the gate is doing. For a gate stuck open or a gate that won’t close, we prioritize those calls. Call (682) 432-9830 and we’ll give you a live arrival window on the spot.

Written by Nico Alvarez, Owner, Calder Gate Repair Fort Worth at Calder Gate Repair Fort Worth, serving Fort Worth and nearby areas.