Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Fort Worth?
Gate parts and welding repair in Fort Worth typically runs $150 to $875, with most jobs landing between $200 and $450 before specialty parts. A cracked hinge replacement with a quick weld usually sits at the low end, while full gate frame straightening or custom bracket fabrication pushes toward the top. You’ll pay more when the gate is heavy iron, the damage is structural rather than cosmetic, or the hinges are welded to a stone or brick column instead of a metal post.
Here’s the honest part: gate welding is rarely the expensive line item. It’s the labor to get the gate square again, plus the parts that keep it there. Gate parts and welding in Fort Worth means diagnosing whether you need a $18 hinge, a $90 steel reinforcement plate, or a full weld-and-realign job that runs several hundred dollars. At Calder Gate Repair Fort Worth, you get a written price before any work starts, so the number you agree to is the number on the invoice.
Gate Parts & Welding Cost Breakdown (2026)
These are the prices we see across Fort Worth neighborhoods, from the older iron gates in Arlington Heights and Mistletoe Heights to the newer ornamental steel in Walsh and Chisholm Trail Ranch. Every job gets quoted in writing before work begins.
| Job | Typical Cost Range | What It Includes |
|---|---|---|
| Hinge replacement (weld-on, gate removed) | $150 – $325 | Removing the gate, cutting off the old hinge, welding the new one, rehanging and leveling the gate |
| Hinge replacement (bolt-on) | $95 – $220 | New hinge hardware, alignment check, gate adjustment |
| Crack repair (single weld point) | $120 – $260 | Surface prep, weld, grind smooth, rust-inhibiting primer on the repair area |
| Gate frame straightening | $250 – $575 | Heat or hydraulic straightening of a bent frame member, weld reinforcement if needed |
| Custom bracket or plate fabrication | $180 – $400 | Cutting and welding a custom steel bracket, hinge plate, or reinforcement gusset on site |
| Full gate removal, weld repair, and rehang | $325 – $875 | Includes removal, structural repair, rehanging, opener reattachment, and final alignment |
| Sliding gate wheel or track bracket welding | $200 – $450 | Welding the wheel bracket or track guide back into position on cantilevered and V-track gates |
| Driveway gate post repair (metal post) | $150 – $400 | Welding reinforcement to a bent or rusted metal post, checking post plumb |
What drives the price up or down:
- Gate weight. A 14-foot ornamental iron driveway gate weighs a lot more than a 4-foot pedestrian gate. The heavier the gate, the more effort it takes to remove, reposition, and rehang. Heavy gates often need a lift assist or a second technician, which adds labor.
- Hinge style and column material. Welded hinges on a steel post are straightforward. Hinges embedded in stone or brick columns take longer because the technician has to work around the masonry without damaging it. In older Fort Worth neighborhoods like Fairmount and Ryan Place, we see a lot of brick column work on 1920s and 1930s gates.
- Access to both sides of the gate. If the hinge side is tight against a fence line or landscaping, the technician may need to remove panels or work at an awkward angle. That adds time.
- Rust and metal fatigue. North Texas clay soil holds moisture against gate posts, and Fort Worth summers bake the paint off. The combination means rust runs deeper than it looks. A simple-looking crack often reveals thin metal that needs a reinforcement plate.
- Opener involvement. If the gate has an opener, the technician has to unhook the arm, reset the limits after rehanging, and make sure the open and close cycles still line up. That’s extra labor, but it’s the right way to do it. We train on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule so the opener doesn’t fight the repair.
What Affects Gate Parts & Welding Pricing in Fort Worth
Several local factors move Fort Worth numbers around. These aren’t excuses, just the realities of repairing metal in this climate and this city.
- Soil movement. Fort Worth sits on expansive clay that swells when wet and shrinks when dry. This seasonal heaving slowly pushes gate posts out of plumb, which puts stress on hinges and welds. A gate that worked fine in March can bind by August. Repairs here often include realigning the gate, not just patching the weld.
- Heat and UV exposure on paint. Fort Worth gets 230+ sunny days a year. That bakes the protective coating off steel gates over time, especially the south-facing side. Exposed metal rusts, and rust weakens welds. Expect the repair estimate to include surface prep and a rust-inhibiting primer so the fix lasts longer than a year.
- Gate style and age. The older ornamental iron gates in Berkeley Place and Park Hill often have hand-forged components that don’t match modern stock parts. Custom fabrication for a decorative finial or a curved rail bracket adds cost compared to a standard square-tube gate in a newer development.
- Hinge and weld point count. A single cracked hinge is a one-hour job. A gate with four failing weld points and two bent frame members is a half-day job. We itemize this in the written quote, so you see exactly where the hours go.
- Column or post material. Steel posts are fast to weld to. Stone, brick, or stucco columns require careful anchoring and sometimes a custom wrap bracket. The labor difference can be $100 to $250 on the same gate style.
- Opener compatibility. Some older openers, particularly certain FAAC and older Mighty Mule models, have shorter arms that tolerate less gate sag. After a weld repair, we check the travel limits and the obstruction settings so the gate doesn’t work against the new weld. That check adds a small amount of labor but prevents repeat failures.
Gate Parts & Welding: How the Repair Process Works
If you’ve never had a gate welded before, here’s what actually happens from the phone call to the finished job. Calder Gate Repair Fort Worth answers every call with a live person, 24/7, so the first step is simple: tell us what the gate is doing.
- Call and describe the problem. A live person answers, not a call center. We’ll ask what the gate is doing: sagging, dragging on the ground, a broken hinge, a crack in the frame, or an opener that’s grinding. We’ll also ask about the gate material and size so the technician arrives with the right parts and welding equipment.
- Get a written price on site. The technician inspects the gate, finds every weld point that’s failing, and writes up a line-item price before touching a tool. You approve the number, and that’s the number you pay. No surprises after the work starts.
- Gate removal and prep. For hinge and frame repairs, the gate comes off the post. The area around each weld point gets ground down to clean metal. Rust, old paint, and previous weld slag all come off, because welding over contamination makes a weak joint.
- Weld and reinforce. The technician welds each joint, then checks whether the surrounding metal is too thin to hold long-term. If it is, they’ll add a reinforcement plate or gusset and weld that in too. New steel goes on thick, not thin.
- Prime and protect the repair. Every repaired area gets a rust-inhibiting primer. If you want us to match paint on the visible parts, we’ll note that in the quote at the start.
- Rehang and align the gate. The gate goes back on the hinges, gets leveled, and the swing or slide action gets checked. If there’s an opener, we reconnect the arm, reset the travel limits, and cycle the gate open and closed several times to confirm it works smoothly.
- Final walkthrough and invoice. You get before-and-after photos and a digital invoice you can pay from a link. The 365-Day Done Right Promise is written on the invoice: if the repair fails within 365 days, Calder returns at no charge.
Common Gate Parts We Replace in Fort Worth
Most gate part failures fall into a handful of categories. Here’s what we replace most often, with local context on why each one fails.
Weld-on hinges
The hinge is the highest-stress point on any gate. When a weld-on hinge starts to fail, you’ll see the gate drop on the latch side, scrape the driveway, or shift when the wind catches it. In Fort Worth, the freeze-thaw cycles in winter plus the summer heat expansion work the welds loose over years. A single new weld-on hinge typically runs $18 to $45 for the part, with labor bringing the total to $150 to $325 installed.
Gate wheels and rollers
Sliding gates ride on steel or nylon wheels. The steel wheels on cantilevered gates take the full weight and get flat spots. Nylon wheels on V-track gates crack in the heat. Replacement wheels run $30 to $90, and if the wheel bracket is bent or cracked, it needs a weld repair at the same time. Total jobs in this category usually land between $200 and $450.
Strike plates and latch posts
The strike plate is the metal bracket that receives the latch bolt. When a gate sags, the latch misses the strike or slams into it, bending the plate and wallowing out the screw holes. A new strike plate is $15 to $50, but the real fix is correcting whatever made the gate sag in the first place.
Limit switches
A limit switch is the small sensor that tells the gate opener when to stop. When a weld repair changes the gate’s travel path even slightly, the old limit switch settings are wrong. Switches themselves are $25 to $70, and we adjust them as part of any opener-involved repair rather than charging for a separate trip.
Reinforcement plates and gussets
When the original steel is too thin from rust, the right fix is a reinforcement plate welded over the weak area. A custom-cut plate, shaped and welded on site, adds $60 to $150 in parts and labor to a repair, but it’s what keeps the gate from failing again at the same spot in six months.
How to Save on Gate Parts & Welding
Gate repair is one area where trying to save money up front usually costs more later. But there are legitimate ways to keep the bill down without cutting corners.
- Catch the problem when it’s a $25 part, not a $400 frame job. A gate that’s dragging slightly or squeaking at the hinge is telling you something. Fixing the hinge before the frame bends saves hundreds. If you notice a change in how the gate swings, call us. A live person answers 24/7 and can help you figure out whether it’s urgent.
- Don’t let rust go another summer. Rust on the bottom hinge area spreads fast in Fort Worth humidity. A quick weld repair with primer in the spring costs less than a frame reconstruction in October. Treat surface rust when you first see it.
- Bundle related repairs into one trip. If the gate needs a hinge weld and the opener arm is worn, doing both in a single visit saves the second service call. The technician can assess everything on site and give you one written price for the whole job.
- Ask about the right opener settings after a weld. A gate that slams or travels too far after a repair will re-break the weld. We reset the limit switches and force settings on every opener-involved repair as standard practice. It costs nothing extra but prevents a repeat call.
- Get the free estimate and the written price. Calder Gate Repair Fort Worth gives you a written price before any work starts. You can compare it line by line. The number on the quote is the number on the invoice. Call (682) 432-9830 for a free estimate on any gate parts or welding job.
Older Wrought Iron and Ornamental Gates in Fort Worth
Fort Worth has more old ornamental iron than most Texas cities, mostly in the historic districts and the neighborhoods that grew up around them. These gates aren’t welded the same way as a modern steel tube gate, and the repair approach has to respect that.
Old wrought iron is actually softer and more forgiving than modern mild steel. It welds well, but the surrounding metal may have internal fractures you can’t see until you clean the paint off. When we repair an ornamental gate in Fairmount or Ryan Place, we grind back further than we would on a newer gate, looking for secondary cracks. It adds a few minutes per weld point, but it prevents the frustrating situation where one weld fails and the next joint breaks a month later.
Decorative elements also matter here. If a scroll or finial is involved, the repair has to match the visual rhythm of the gate, not just be structurally sound. Our welders shape and finish ornamental repairs so they don’t look like patch jobs, then prime and leave the area ready for matching paint. Expect ornamental work to run 15 to 30 percent higher than a comparable straight steel repair because of the extra prep and finishing time.
FAQs – Gate Parts & Welding Cost
How much does it cost to weld a gate hinge in Fort Worth?
Welding a single gate hinge in Fort Worth typically costs $150 to $325, including removing the gate, cleaning the weld area, welding the new hinge, and rehanging the gate level and aligned. If the hinge is bolt-on and no welding is needed, the same job runs $95 to $220. Call (682) 432-9830 for a written quote on your specific gate.
Is it cheaper to repair or replace a gate in Fort Worth?
Repair is almost always cheaper. A full weld repair, hinge replacement, and realignment typically runs $325 to $875, while a new custom ornamental gate in Fort Worth starts around $1,800 to $4,500 installed. If the frame is structurally sound and the rust hasn’t eaten through major sections, repair makes sense. We’ll tell you honestly which one applies to your gate.
How much does it cost to fix a sagging gate?
Fixing a sagging gate in Fort Worth typically costs $150 to $450 when the cause is a worn hinge or a single failed weld. If the sag comes from a bent or rust-thinned frame section, the repair runs $325 to $875 because the frame needs straightening or reinforcement, not just a hinge swap. A sagging gate that scrapes the driveway is a sign that a weld or hinge has failed, so the sooner it’s addressed, the lower the bill.
Can you weld an aluminum gate?
Yes, aluminum gates can be welded, but it requires a different process than steel. Aluminum welding in Fort Worth typically runs $200 to $600 depending on the repair size, because the technician needs specialized equipment and the aluminum must be scrupulously clean. Many aluminum gate failures are actually at the bolted connections, which can be repaired for $95 to $220. Call (682) 432-9830 and we’ll tell you what your gate actually needs.
Can you come fix my gate the same day?
In most cases, yes. Calder Gate Repair Fort Worth answers calls with a live person 24/7, and we dispatch background-checked, uniformed technicians with a live, trackable arrival time, not a vague four-hour window. Same-day gate welding is available across Fort Worth, including downtown, Near Southside, TCU, and the Alliance area. Call (682) 432-9830 and we’ll give you a real arrival time over the phone.
Do you guarantee gate welding work?
Yes. Every gate welding and parts repair from Calder Gate Repair Fort Worth carries the 365-Day Done Right Promise, written on the invoice. If the repair fails within 365 days, we return at no charge. You also get a written price before any work starts and a free second visit if the repair doesn’t hold. That’s not an optional add-on; it’s on every job.
Gate Parts & Welding in Fort Worth: Call for a Free Estimate
Gate problems don’t fix themselves, and a sagging or cracked gate only gets more expensive the longer it sits. Calder Gate Repair Fort Worth is the dedicated gate repair specialist inside the Relay Home Co. family, and we’ve been doing this work since 2009. Our technicians are factory-familiar with LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule openers, so when the weld repair is done, your opener works with the gate, not against it.
Every job comes with the three things you should expect from any contractor: a written price before work starts, a written guarantee on every repair, and a free second visit if the repair fails within 365 days. A live person answers every call, day or night. No voicemail, no call center, no four-hour window.
Call (682) 432-9830 for a free estimate on gate parts, welding, or any gate repair in Fort Worth. We’ll tell you what it costs, what it needs, and when we can be there.
Written by Nico Alvarez, Owner at Calder Gate Repair Fort Worth, serving Fort Worth since 2009.
Pricing reflects the Fort Worth market as of 2026. Calder Gate Repair Fort Worth offers free estimates – call (682) 432-9830.
What Our Customers Say
"Safety sensors realigned. Works fine. Photo eyes were dirty and out of line. Gate now stops when it should."
- Raul A."Booking was easy and the job was done quickly."
- Seth R."Slide gate wheels replaced. Glides smoothly now."
- Mark T.